|
Low cost alternative to Scrim Vinyl material provides a great solution
for all your short term indoor and outdoor banner applications. Its
high opacity minimizes sunlight show-through and its matte finish
reduces glare. Its unique inkjet coating allows for high-end,
water-resistant imaging when using UV/Pigmented inks.
42"x100' roll on 2" core. 1 roll per box.
Physical Properties
Caliper .0092”
Whiteness 102
Gloss 60º 2.1
Opacity 97%
Outdoor Life Expectancy 1 Months
Indoor Life Expectancy 6 Months
Flame Spread Classification Class B (ASTM E-84)
Tensile Strength (MD/CD) 50/65 lbs/in
Ultimate Elongation (MD/CD) 150/90%
Usage Guidelines
Calibration
It’s always best to calibrate (linearize) your printer each and every
time you change media and/or ink sets. Refer to printer manual for
specific instructions on calibration.
Media Handling
Once complete, store your finished image in roll form. Avoid excessive
folding of Scrim Vinyl. Image output can vary from lot to lot. It is
recommended that multiple (same job) printing should be printed using
the same lot number materials.
Storage Conditions
Store media in a cool, dry area in temperatures of 70°F (21°C) and
20-60% relative humidity. Always store unused media in its original
packaging.
Water Resistance
The best water resistance will be obtained using pigmented inks. Dye
based inks can be used, however exposure to moisture can result in
bleeding of the image. To eliminate bleed possibilities for a dye-based
image, encapsulate the image with lamination. Let image dry for at
least 24 hours before exposure to moisture.
Surface Protection
Dirt and stains cannot be cleaned from the imaged surface. Excessive
handling, folding or creasing can cause damage to the image surface.
Lamination is recommended to protect image from dirt, abrasion and
excessive handling.
Lamination
Lamination is not required; but can add additional surface protection.
Pressure sensitive over-laminates are recommended. Laminating one side
only may cause product to curl toward laminated side. Let image dry 24
hours before laminating.
Finishing
For stitched hems, a double stitched hem is recommended. Use a maximum
of 5 stitches per inch. And, keep in mind that the inkjet image can be
scratched, so it’s recommended that the banner be sewn from the hem
side up. This will keep the sewing machine foot from coming in contact
with the image. For a taped hem, use standard high-tack banner tape.
Always follow the tape manufacturer’s guidelines.
Inks
The best degree of water resistance will be obtained by utilizing
pigment-based inks. Recommended ink coverage is 250% or less. Heavier
ink saturation could degrade the water-fast characteristics. Encad GX™,
Ilford Archiva™, and Colorspan EnduraChrome™ Inks are not recommended,
as premature aging may occur. Dye-based inks can be
used with good
success, however, repeated moisture exposure to dye-based inks may
cause bleeding and premature fade can occur. Although lamination is not
required for pigmented inks, lamination is recommended when using
dye-based inks. Total encapsulation is recommended to eliminate the
possibility of bleed when using dyebased inks. Image should be left to
dry for 24 hours before exposure to moisture.
|
AZONcolor Indoor/Outdoor Polypropylene Banner is compatible with the following products: |  | | HP Designjet 1050c Plus Printer (C6074B)
HP Designjet 1055cm Plus Printer (C6075B)
HP Designjet 500 42-in Roll Printer (C7770B)
HP Designjet 5000 Printer (C6095A)
HP Designjet 5000 UV Printer (C6090V)
HP Designjet 5000ps Printer (C6096A)
HP Designjet 5000ps UV Printer (C6096V)
HP Designjet 510 42-in Printer (CH337A)
HP Designjet 5500 Printer (42 in) (Q1251A)
HP Designjet 5500 Printer (60 in) (Q1253A)
HP Designjet 5500PS Printer (42 in) (Q1252A)
HP Designjet 5500PS Printer (60 in) (Q1254A)
HP Designjet 5500UV Printer (42 in) (Q1251V)
HP Designjet 5500UV Printer (60 in) (Q1253V)
HP Designjet 5500UVPS Printer (42 in) (Q1252V)
HP Designjet 5500UVPS Printer (60 in) (Q1254V)
HP Designjet 800 Printer (42 in) (C7780B)
HP Designjet 800ps Printer (42 in) (C7780C)
HP Designjet 815mfp (Q1279A)
HP Designjet 820 MFP (Q6685A)
HP Designjet T1100 MFP (Q6713A)
HP Designjet Z2100 44-in Photo Printer (Q6677A)
HP Designjet Z3100 44-in Photo Printer (Q6659A)
HP Designjet Z3100ps GP 44-in Photo Printer (Q6660A)
HP Designjet Z6100 42-in Printer (Q6651A)
HP Designjet Z6100 60-in Printer (Q6652A)
HP Designjet Z6100ps 42-in Printer (Q6653A)
HP Designjet Z6100ps 60-in Printer (Q6654A)
|
|
