|
Low cost alternative to Scrim Vinyl material provides a great solution for all your short term indoor and outdoor banner applications. Its high opacity minimizes sunlight show-through and its matte finish reduces glare. Its unique inkjet coating allows for high-end, water-resistant imaging when using UV/Pigmented inks.
24"x60' roll on 2" core. 1 roll per box.
Physical Properties
Caliper .0092”
Whiteness 102
Gloss 60º 2.1
Opacity 97%
Outdoor Life Expectancy 1 Months
Indoor Life Expectancy 6 Months
Flame Spread Classification Class B (ASTM E-84)
Tensile Strength (MD/CD) 50/65 lbs/in
Ultimate Elongation (MD/CD) 150/90%
Usage Guidelines
Calibration It’s always best to calibrate (linearize) your printer each and every time you change media and/or ink sets. Refer to printer manual for specific instructions on calibration.
Media Handling Once complete, store your finished image in roll form. Avoid excessive folding of Scrim Vinyl. Image output can vary from lot to lot. It is recommended that multiple (same job) printing should be printed using the same lot number materials.
Storage Conditions Store media in a cool, dry area in temperatures of 70°F (21°C) and 20-60% relative humidity. Always store unused media in its original packaging.
Water Resistance The best water resistance will be obtained using pigmented inks. Dye based inks can be used, however exposure to moisture can result in bleeding of the image. To eliminate bleed possibilities for a dye-based image, encapsulate the image with lamination. Let image dry for at least 24 hours before exposure to moisture.
Surface Protection Dirt and stains cannot be cleaned from the imaged surface. Excessive handling, folding or creasing can cause damage to the image surface. Lamination is recommended to protect image from dirt, abrasion and excessive handling.
Lamination Lamination is not required; but can add additional surface protection. Pressure sensitive over-laminates are recommended. Laminating one side only may cause product to curl toward laminated side. Let image dry 24 hours before laminating.
Finishing For stitched hems, a double stitched hem is recommended. Use a maximum of 5 stitches per inch. And, keep in mind that the inkjet image can be scratched, so it’s recommended that the banner be sewn from the hem side up. This will keep the sewing machine foot from coming in contact with the image. For a taped hem, use standard high-tack banner tape. Always follow the tape manufacturer’s guidelines.
Inks The best degree of water resistance will be obtained by utilizing pigment-based inks. Recommended ink coverage is 250% or less. Heavier ink saturation could degrade the water-fast characteristics. Encad GX™, Ilford Archiva™, and Colorspan EnduraChrome™ Inks are not recommended, as premature aging may occur. Dye-based inks can be
used with good success, however, repeated moisture exposure to dye-based inks may cause bleeding and premature fade can occur. Although lamination is not required for pigmented inks, lamination is recommended when using dye-based inks. Total encapsulation is recommended to eliminate the possibility of bleed when using dyebased inks. Image should be left to dry for 24 hours before exposure to moisture.
|
AZONcolor Indoor/Outdoor Polypropylene Banner is compatible with the following products: |  | | HP Designjet 1050c Plus Printer (C6074B)
HP Designjet 1055cm Plus Printer (C6075B)
HP Designjet 500 42-in Roll Printer (C7770B)
HP Designjet 5000 Printer (C6095A)
HP Designjet 5000 UV Printer (C6090V)
HP Designjet 5000ps Printer (C6096A)
HP Designjet 5000ps UV Printer (C6096V)
HP Designjet 510 42-in Printer (CH337A)
HP Designjet 5500 Printer (42 in) (Q1251A)
HP Designjet 5500 Printer (60 in) (Q1253A)
HP Designjet 5500PS Printer (42 in) (Q1252A)
HP Designjet 5500PS Printer (60 in) (Q1254A)
HP Designjet 5500UV Printer (42 in) (Q1251V)
HP Designjet 5500UV Printer (60 in) (Q1253V)
HP Designjet 5500UVPS Printer (42 in) (Q1252V)
HP Designjet 5500UVPS Printer (60 in) (Q1254V)
HP Designjet 800 Printer (42 in) (C7780B)
HP Designjet 800ps Printer (42 in) (C7780C)
HP Designjet 815mfp (Q1279A)
HP Designjet 820 MFP (Q6685A)
HP Designjet T1100 MFP (Q6713A)
HP Designjet Z2100 44-in Photo Printer (Q6677A)
HP Designjet Z3100 44-in Photo Printer (Q6659A)
HP Designjet Z3100ps GP 44-in Photo Printer (Q6660A)
HP Designjet Z6100 42-in Printer (Q6651A)
HP Designjet Z6100 60-in Printer (Q6652A)
HP Designjet Z6100ps 42-in Printer (Q6653A)
HP Designjet Z6100ps 60-in Printer (Q6654A)
|
|
